Macros
#define	__HAL_RCC_RTC_ENABLE() ((__IO uint32_t ) RCC_BDCR_RTCEN_BB = ENABLE)
	Macros to enable or disable the RTC clock. More...

#define	__HAL_RCC_RTC_DISABLE() ((__IO uint32_t ) RCC_BDCR_RTCEN_BB = DISABLE)

#define	__HAL_RCC_RTC_CLKPRESCALER(__RTCCLKSource__)
	Macros to configure the RTC clock (RTCCLK). More...

#define	__HAL_RCC_RTC_CONFIG(__RTCCLKSource__)

#define	__HAL_RCC_BACKUPRESET_FORCE() ((__IO uint32_t ) RCC_BDCR_BDRST_BB = ENABLE)
	Macros to force or release the Backup domain reset. More...

#define	__HAL_RCC_BACKUPRESET_RELEASE() ((__IO uint32_t ) RCC_BDCR_BDRST_BB = DISABLE)

Detailed Description

Macro Definition Documentation

◆ __HAL_RCC_BACKUPRESET_FORCE

#define __HAL_RCC_BACKUPRESET_FORCE ( ) (*(__IO uint32_t *) RCC_BDCR_BDRST_BB = ENABLE)

Macros to force or release the Backup domain reset.

Note: This function resets the RTC peripheral (including the backup registers) and the RTC clock source selection in RCC_CSR register.; The BKPSRAM is not affected by this reset.

◆ __HAL_RCC_RTC_CLKPRESCALER

#define __HAL_RCC_RTC_CLKPRESCALER ( __RTCCLKSource__ )

Value:

(((__RTCCLKSource__) & RCC_BDCR_RTCSEL) == RCC_BDCR_RTCSEL) ? \

MODIFY_REG(RCC->CFGR, RCC_CFGR_RTCPRE, ((__RTCCLKSource__) & 0xFFFFCFFU)) : CLEAR_BIT(RCC->CFGR, RCC_CFGR_RTCPRE)

Macros to configure the RTC clock (RTCCLK).

Note: As the RTC clock configuration bits are in the Backup domain and write access is denied to this domain after reset, you have to enable write access using the Power Backup Access macro before to configure the RTC clock source (to be done once after reset).; Once the RTC clock is configured it can't be changed unless the Backup domain is reset using __HAL_RCC_BackupReset_RELEASE() macro, or by a Power On Reset (POR).

Parameters

<strong>RTCCLKSource</strong>

specifies the RTC clock source. This parameter can be one of the following values:

RCC_RTCCLKSOURCE_LSE: LSE selected as RTC clock.
RCC_RTCCLKSOURCE_LSI: LSI selected as RTC clock.
RCC_RTCCLKSOURCE_HSE_DIVx: HSE clock divided by x selected as RTC clock, where x:[2,31]

Note: If the LSE or LSI is used as RTC clock source, the RTC continues to work in STOP and STANDBY modes, and can be used as wake-up source. However, when the HSE clock is used as RTC clock source, the RTC cannot be used in STOP and STANDBY modes.; The maximum input clock frequency for RTC is 1MHz (when using HSE as RTC clock source).

◆ __HAL_RCC_RTC_CONFIG

#define __HAL_RCC_RTC_CONFIG ( __RTCCLKSource__ )

Value:

do { __HAL_RCC_RTC_CLKPRESCALER(__RTCCLKSource__);    \
                                                    RCC->BDCR |= ((__RTCCLKSource__) & 0x00000FFFU);  \
                                                   } while (0)

◆ __HAL_RCC_RTC_ENABLE

#define __HAL_RCC_RTC_ENABLE ( ) (*(__IO uint32_t *) RCC_BDCR_RTCEN_BB = ENABLE)

Macros to enable or disable the RTC clock.

Note: These macros must be used only after the RTC clock source was selected.